DESIGN AND FABRICATION OF BASIC STATIC AND DYNAMIC BALANCING MACHINE
ABSTRACT
This work is an attempt to evolve a means for statically and dynamical balancing of mechanical components. This will no doubt evolve greater success in ensuring sound fabrication of our local machine and ensuring that life span of such machine is prolonged since vibration will be reduced to the bearest minimum.
Every wheel and its shaft have to be in a state of balanced, two mating shaft in rotation have to be in a state of static and dynamic balance. This is because unbalance condition produce centrifugal force which increase as the speed of the machine increase, causing damage to machine parts.
To achieve the aim of static and dynamic balancing, various design alternatives for achieving the design solution were synthesized and a choice of economic method which will satisfy the objective was made. Based on the principle guiding the performance of the machine, the dimension and size of the various components was were established and correctly selected and the basic static and dynamic apparatus was fabricated and after testing it was found to satisfy the objective.
CHAPTER ONE
1.0 Introduction
Power transmission in engineering is accomplished by the use of shafts bearings, pulleys, belts, rollers, gears, couplings, etc. Most machine members are linked or interconnected with one another before this power transmission can be effective.
Misalignment or out of balance of shafts or any of these machine members results in excessive viberation which is transmitted to other members and down to the foundation bolt and therefore in fatigue stress on the members. Fatigue, probably, is responsible for over 70% of failure of engineering component in operation. Misalignment in shafts and bearing causes excessive load. High speed bearing of aircrafts that may operate at over 20,000 rpm may become catastrophic if there be any unbalance of the members. Out of balance of machine members creates serious problems on the functionality and durability and machine members and on the machine in general.
It is therefore, with the understanding of he sensitivity of balancing in the design of mechanical components and the need to put balancing into consideration in the fabrication of our local machines, the view to determine the level of out of balance and the subsequent balancing of these machine members that necessitated the idea of designing and constructing a Basic Static and Dynamic Balancing Apparatus of this nature.
1.1 Objectives
The objective of this project is to design, construct and test a basic static and dynamic balancing apparatus as one of the ways to prevent premature failure of engineering components due to fatigue loading.
1.2 Scope of the Project
The basic and dynamic balancing machine covers the fundamental exploits of knowledge to design and construct and static and dynamic balance for any mechanical member since each machine components has its own balance depending on its bulkiness. The basic principle of construction lies on the one chained in our construction. This construction gives illumination for the construction of production and maintenance balance. It also serves as a means of demonstrating static and dynamic balancing in laboratories of higher learning.
CHAPTER TWO
2.0 Literature Review
2.1 Introduction
The review of relevant literature is the main topic of this chapter. A literature review covers theoretical and methodological contributions to a certain issue in addition to the state of knowledge at the time of writing. It provides information about the state of the art in relation to the subject you are writing about. It examines the body of work on the chosen subject. The literature evaluation in this study comprises the …
Procedure for Downloading the PDF (Docx) Material
Design and Fabrication of Basic Static and Dynamic Balancing Machine can be downloaded by requesting the full set of materials at the project or seminar cost. The document will be sent via Microsoft Word (MS-Word) format via WhatsApp (e-mail) following payment confirmation.
| Seminar Material Cost ₦3,000 | Project Material Cost ₦5,000 |
Request Complete Material
 | Click here to request the Complete Material via WhatsApp including;
|
TABLE OF CONTENTSPRELIMINARY PAGES
- Title page
- Approval page
- Dedication
- Acknowledgement
- Table of Contents
- Abstract
- 1.0 Introduction
- 1.1 Objective
- 1.2 Scope of the Project
- 2.0 Literature Review
- 2.1 What is Balancing
- 2.2 Type of Unbalance
- 2.2.1 Static Unbalance
- 2.2.2 Couple Unbalance
- 2.2.3 Dynamic Unbalance
- 2.3 Balancing Equipments
- 3.0 Specification of Problem/Synthesis of Solution and Theory of Design
- 3.1 Background Information/Objective
- 3.2 Definition
- 3.3 Condition of Use
- 3.4 Characteristics
- 3.5 Performance
- 3.6 Reliability
- 3.7 Synthesis of Solution
- 3.8 Theory of Design
- 3.8.1 Machine Element and Forces
- 3.8.2 Balancing of Rotating Masses
- 3.8.3 Out of balance masses in a common transverse Plane
- 3.8.4 Out of Balance Masses in Different Transverse Plane
- 4.0 Design Calculation of Basic Static and Dynamic Balance Machine
- 4.1 Approximate Weight of the Balancing Weight
- 4.2 Force Analysis on Shaft
- 4.3 Shear Force (SF) Calculation
- 4.4 Bending Moment Calculation
- 4.5 Shaft Design
- 4.6 Motor Belt Analysis
- 4.7 Bearing Selection
- 5.0 Fabrication Procedure/Material Selection/Principle of Operation and Cost Analysis
- 5.1 Assembly Process
- 5.2 Material Selection
- 5.3 Principle of Operation
- 5.4 Cost Analysis
- 5.5 Conclusion and Recommendation
REFERENCES
APPENDIX
Disclaimer for Complete Material Utilization
The displayed research work titled "Design and Fabrication of Basic Static and Dynamic Balancing Machine" is stated as a research guideline towards accomplishing your assigned project / seminar research work. All the research materials on this website are ONLY for research purposes and should be used as a guideline in developing your research work. For no reason should you copy word for word as projectlist.com.ng will not be liable for any who copied the material. By ordering the complete research guideline, it signifies that you've accepted our terms of service.
PRELIMINARY PAGES
- Title page
- Approval page
- Dedication
- Acknowledgement
- Table of Contents
- Abstract
- 1.0 Introduction
- 1.1 Objective
- 1.2 Scope of the Project
- 2.0 Literature Review
- 2.1 What is Balancing
- 2.2 Type of Unbalance
- 2.2.1 Static Unbalance
- 2.2.2 Couple Unbalance
- 2.2.3 Dynamic Unbalance
- 2.3 Balancing Equipments
- 3.0 Specification of Problem/Synthesis of Solution and Theory of Design
- 3.1 Background Information/Objective
- 3.2 Definition
- 3.3 Condition of Use
- 3.4 Characteristics
- 3.5 Performance
- 3.6 Reliability
- 3.7 Synthesis of Solution
- 3.8 Theory of Design
- 3.8.1 Machine Element and Forces
- 3.8.2 Balancing of Rotating Masses
- 3.8.3 Out of balance masses in a common transverse Plane
- 3.8.4 Out of Balance Masses in Different Transverse Plane
- 4.0 Design Calculation of Basic Static and Dynamic Balance Machine
- 4.1 Approximate Weight of the Balancing Weight
- 4.2 Force Analysis on Shaft
- 4.3 Shear Force (SF) Calculation
- 4.4 Bending Moment Calculation
- 4.5 Shaft Design
- 4.6 Motor Belt Analysis
- 4.7 Bearing Selection
- 5.0 Fabrication Procedure/Material Selection/Principle of Operation and Cost Analysis
- 5.1 Assembly Process
- 5.2 Material Selection
- 5.3 Principle of Operation
- 5.4 Cost Analysis
- 5.5 Conclusion and Recommendation
REFERENCES
APPENDIX
Disclaimer for Complete Material Utilization
The displayed research work titled "Design and Fabrication of Basic Static and Dynamic Balancing Machine" is stated as a research guideline towards accomplishing your assigned project / seminar research work. All the research materials on this website are ONLY for research purposes and should be used as a guideline in developing your research work. For no reason should you copy word for word as projectlist.com.ng will not be liable for any who copied the material. By ordering the complete research guideline, it signifies that you've accepted our terms of service.
Frequently Asked Questions (FAQ)
Can the material for “Assessment of Patient Attitude to the Involvement of Students in Radiographic Examinations in Hospitals” be used as a guide for Radiography Project?
Yes it can be used — Patients' consent to being part of the education of Medical Radiography is often taken for granted hence formal consent is not always sought during teaching and patients are sometimes not aware that they are going to be used for teaching activities. Some students of Radiography are not even aware of patients' right to privacy when they come for radiographic examinations. This study aims to assess the reaction or attitude of patients to the involvement of students in radiographic examinations. A survey was conducted using a manual questionnaire tailored to suit the purpose of this study; data collected from patients from the three university teaching hospitals in Enugu namely UNTH, NOHE and ESUTH (N=99) was statistically analyzed. The results show that 22.2% …
Can this topic “Design and Construction of a Metal Detector” be used for Electrical / Electronics Engineering (EE) Project?
Yes it can be utilized for research — A metal detector is a device which responds to metal that may not be readily apparent. This system detects metals of different types and also electronics gadgets such as cell phone, bombs etc. it work in such a way that when such devices are brought close to it, it detects it by giving out a beep. The research work was conducted to design and construct a metal detector. In achieving this aim, the following specific objectives were laid out to construct a walk through metal detector that is capable of detecting the presence of a metallic device and walk through metal detector world also incorporate the functionality of metallic object. This will stop or reduce to the barest minimum the …
Is the topic “Management of Organizational Conflict in Government Agency” recommended for Business Administration and Management (BAM) Project?
Yes it is highly recommended — The cause of conflict, it’s consequences and the management of conflict in the Nigerian security printing and miniting company limited have been studied in this project. Survey questionnaires was adopted in collection of data. Respondents were drawn equally from all the departments of the company. Sample selection was by stratified probability sampling and it constitutes only the senior employees of the company. Data generator were analyzed using single percentage. Question were drawn is such a way that enabled the respondents the opportunity to express their consequences and ways it can be effectively managed. The result and findings of the study revealed that the causes of conflict in the Nigeria security, printing and miniting company limited was largely due to lack …
Can this topic “Quality Assessment of Soybean Ogiri Produced with Melon Seed Ogiri Inoculum” be used for Food Science and Technology (FT) Project?
Yes it can be utilized for research — This study examines the Quality of “Ogiri” produced from Soybean inoculated with fermented melon seed isolate. The result for the proximate analysis showed that the Fat Content is 5.50%, Moisture Content is 40.09%, Ash Content is 1.30%, Crude Fibre is 3.00%, Protein is 27.56% and Carbohydrate is 22.55%. …
Is the topic “The Reduction of Rural-Urban Migration in Nigeria through Rural Management” recommended for Estate Management (EM) Project?
Yes it is highly recommended — Rural resources have a lot of potential which needed to be brought into full production as to uplift the values. These values can only be achieved when other resources like times, money, infrastructure, expertise an d the like are applied. The high demand of products is expected to propel the application of the said resources into maximum production which in turn increase the value of rural environment, confirming value to be a function of profit. Unfortunately, government policies and programmes in the year past failed to reflect the need for balance rural and urban development. Thus, most development polices and programmes are urban − oriented. As a result rural dwellers have been subjected to poverty, unemployment, poor infrastructure, economic and social …
Can the material for “Critical Discourse Analysis in Ola Rotimi’s Our Husband has Gone Mad Again” be used as a guide for Linguistics and Communication Project?
Yes it can be used — The purpose of this project is to critically analyze the Proverbs titled Our Husband has Gone Mad Again by Ola Rotimi using Critical Discourse Analysis. Being that the analysis of a play is rarely done, the researcher is not aware of any previous attempt to do Critical Discourse Analysis of the text Our Husband has Gone Mad Again. Analysis on a conversation level has been used in the analysis of texts, but this study attempts to carry out Critical Discourse Analysis of Ola Rotimi’s Our Husband Has Gone Mad Again. The Norman Fair clough theory has been applied in this approach, paying more attention on the socio cultural and political issues in the text. The text is a social drama …
Can this topic “Design and Implementation of a Computerized Administration of a Local Government Personnel Auditing System” be used for Computer Science (CS) Project?
Yes it can be utilized for research — A Computerized personnel auditing system is an application software that executes a recurring evaluation to assess the efficiency of personnel management and identify the actions necessary for optimizing the use of human resources. The aim of the study is to design and implement a Computerized Personnel Auditing System. In achieving this aim, the following specific objectives were laid out to develop an application that will give a more accuracy and timely information for government decision making, and provide facilities for quick access to stored data giving at random in other to assist in management functions. The motivation that led to the implementation of the proposed system is that the accumulation of this document in files creates low of storage problem …
Can the material for “Appraisal of the Use of Automated Teller Machine (ATM) in the Banking Industry” be used as a guide for Computer Science Education Project?
Yes it can be used — This work is based on the appraisal of the Automated Teller Machine. It involves the use of Diffusion of Innovation (DOI) model which comprises of the relative advantage, compatibility, complexity, trialability, observability for the analysis of data collected. Data was collected through the administration of questionnaires’ to get the needed information from the users and non users of the system. The hypothesis result is stated at the end of the analysis. The major book references are written at the end of the write-up. …
Is the topic “Design and Implementation of Payment Monitoring Information System” recommended for Computer Science (CS) Project?
Yes it is highly recommended — Design and Implementation of an Online Payment Monitoring Information System is a research work that will help build an effective information management system for Ekiti State University within the computer science department. The designed software will serve as a more reliable and effective means of documenting Fees payment and cash payment and eliminate errors associated with the manual method of recording payment details. This project work made use of data collected from the school library, faculty, department and some online websites. The aim of this project work is to achieve the following; to effectively and efficiently process student’s department fees payment and document it, to provide a reliable and transparent system devoid of personal inclinations and interest and to provide …
Is the topic “The Impact of Challenges and Limitations Confronting International Organisation in Carrying Out Humanitarian Aid” recommended for Public Health Project?
Yes it is highly recommended — The aim of the research work was to investigate the impact of challenges and limitations confronting international organization in carrying out humanitarian aid in Nigeria. The primary source of data used for the purpose of this research was the questionnaires for the primary data. Which the secondary data was obtained from journals and other related articles. The method of chi-square was used for the purpose of analysis. The hypothesis to be tested was the effect of crises in carrying out humanitarian aid in Nigeria. At the end of the analysis we found that the p-value was 0.00 which is less than the level of significance so we reject the hypothesis and conclude that crises have significant effect in carrying out …