CONSTRUCTION OF SOAP CUTTING TABLE, SOAP MOULD AND SOAP CUTTERS
ABSTRACT
The construction of soap cutting table, mould and cutters became inevitable as it's importance in our industries and society could not be over emphasized.
When one considers the money at hand, he decides whether to start from the primary production level or secondary production level.
Every establishment starts from the small scale production level. Referring to this project the main aim is for the establishment of small scale soap production machinery and avoid some problems that might arise during the cutting and production level.
Since it is difficult for a poor man to adopt the mechanized method of soap production, the simple soap production machinery was constructed to enable him achieve his aim. in the construction of these project one soap cutting table were made, four moulds of the same dimensions and two pairs of three kinds of cutters.
In the construction work, hard wood were wt and assembled according to the given dimensions for the construction of the soap cutting table and moulds, frames were constructed according to the given dimensions for the cutter's and wire guaza were would ramd them according toe h given space for three types of cutter's.
The hard texture of the wood caused the bending of tools and materials used in the construction process so great skill were applied to minimize damage and great attention were given to the construction procedures.
Finally, after the construction process the soap cutting table was produced to have balance in the four legs, the mould was produced to have handles for easil handling and the three types of cutter has the capacity of cutting cast soap into different size:
- Bar: 390mm x 45mm x 32mm
- Tablet: 90mm x 50mm x 26mm
CHAPTER ONE
1.0 Introduction
The project under analysis and constructional study is the “construction of wooden mould with table and cutters”. in the construction of this soap machine (a wooden contraption), engineering materials like wood, metals or plastics could be used. Though this materials are now grouped into metals and non metals, all based on their physical and chemical characteristics.
In this case of constructing a wooden mould, table and cutters, wood is chosen and is the major engineering material needed. Even though metal has some unique properties over wood and plastic, yet it is desirable in most cases to use some qualitative wood in engineering fabrications and constructions bearing in mind the economy of construction and the life span of the machine.
A well-dried and seasoned hardwood like Mahogany, Froko, Obche etc, can be sued for the construction. This is possible due largely to the fact that wood can resist moisture absorption and weakness unlike metal; it does not corrode and it's also a battery shock absorber when compared with metals.
The increase in demand of soap in our homes, industries and various establishments calls for an efficient, durable, reliable and above all cost — effective means of producing soap. These set of wooden devices the mould, the table and cutters produces a better appeal to the consumers, and also produces tablet and bar soaps that are of quality sizes and also soaps that allows firm grip while use.
This wooden contraption is detachable. The cutters having ranges in their string intervals are occasionally filled in and removed from the cutting table.
This is to allow the proper size reduction of the big and bulky soap to defined bars and tablets of proper sizes.
The devices (the wooden mould, the able and the cutters), are all manually manned. They, being the three composites of a small scale soap cutting machine are interchangeably operated, especially the cutters.
In most industries, especially the small scale industries, cost of producing a given commodity is always a vital factor to be considered. This leads to the invention of a cost effective means and also a cheaper improvisational method of soap production. This idea gave birth to the wooden mould, table and cutters as cost effective machines found in small scale soap industry as compared to the sophisticated steel corrugated tanks, automated cutters and platforms found in large scale soap industries.
CHAPTER TWO
2.0 Literature Review
2.1 Introduction
The review of relevant literature is the main topic of this chapter. A literature review covers theoretical and methodological contributions to a certain issue in addition to the state of knowledge at the time of writing. It provides information about the state of the art in relation to the subject you are writing about. It examines the body of work on the chosen subject. The literature evaluation in this study comprises the …
Procedure for Downloading the PDF (Docx) Material
Construction of Soap Cutting Table, Soap Mould and Soap Cutters can be downloaded by requesting the full set of materials at the project or seminar cost. The document will be sent via Microsoft Word (MS-Word) format via WhatsApp (e-mail) following payment confirmation.
| Seminar Material Cost ₦3,000 | Project Material Cost ₦5,000 |
Request Complete Material
 | Click here to request the Complete Material via WhatsApp including;
|
Disclaimer for Complete Material Utilization
The displayed research work titled "Construction of Soap Cutting Table, Soap Mould and Soap Cutters" is stated as a research guideline towards accomplishing your assigned project / seminar research work. All the research materials on this website are ONLY for research purposes and should be used as a guideline in developing your research work. For no reason should you copy word for word as projectlist.com.ng will not be liable for any who copied the material. By ordering the complete research guideline, it signifies that you've accepted our terms of service.
Frequently Asked Questions (FAQ)
Can the material for “The Causes and Consequences of Cigarette Smoking Among Youth” be used as a guide for Sociology Project?
Yes it can be used — This study is set to examine the causes and consequences of cigarette smoking among youths in Dutsinma local government Area of Katsina State. The study examined the factors responsible for youth involvement in cigarette smoking and its effect on the health and general well-being of youths in the study area. The study employed the quantitative and qualitative research methods to obtain data from the respondents. The stratified random sampling technique was used to select 100 respondents for the study. Questionnaires and indepth interviews methods were used to obtain data from the respondents. Findings of the study revealed that the major factors responsible for cigarette smoking among youths include the need to feel sociable, to chase bore-dam and to feel warm. It …
Is the topic “Construction of Reinforced Concrete Seat” recommended for Civil Engineering Project?
Yes it is highly recommended — The construction of reinforced concrete seat is a project work that deals with the production of reinforced concrete. How reinforced concrete is being produced using the aggregate coarse aggregate cement, water and reinforcement bars. The concrete mixed together in dry state and inter added with water. A formwork was prepared in other to create a shape for the seat that will be produced after the concrete is being poured into the formwork. The fresh concrete was later poured into the form work and allowed to dry. It was cured in other to increase the strength of the concrete. …
Can the material for “Leadership and Corruption in Nigeria Local Government” be used as a guide for Public Administration (PA) Project?
Yes it can be used — The study was carried out to examine the Leadership and Corruption in Nigeria Local Government using Orji River Local Government as a case study. In achieving this aim, the following specific objectives were laid out to identify the areas of corruption and fine out the effect of corruption on the leadership of the local government council in Oji-River Local Government Council. The issue of corruption has remained ever present and continue to grow deep into the vitals of the Nigerian society, most especially as corruption has been ingrained into the fabrics of the Nigerian society cannot be solved overnight because the leaders as well as the followers are corrupt. In light of the above and in recognition of the damage …
Is the topic “The Influence of Social Media on Journalism from the Perspective of Twitter Ban” recommended for Mass Communication (MC) Project?
Yes it is highly recommended — The aim of the study is to investigate the Influence of Social Media on Journalism from the Perspective of Twitter Ban. In achieving this aim, the following specific objective was established below to; know if the journalists are exposed to twitter social media networking tools, find out the usefulness of twitter towards journalists public relation in Nigeria, and determine whether twitter social media have enhanced the productivity of journalists in Nigeria. The influence of social media in today’s world of communication, especially journalism cannot be over-looked. Since its arrival social media have certainly changed the way journalists work, how stories are developed and disseminated. Social media have had positive influences, without doubt, but there are also concerns about their influence …
Can the material for “Effect of Solid Waste on the Quality of Underground Water” be used as a guide for Geography Project?
Yes it can be used — The research paper examines the Effect of Solid Waste on the Quality of Underground Water. In achieving this aim, the specific objectives were set out to; know the physical, chemical and biological effect of Solid Wastes on underground water and determine the amount of wastes within the study areas, determine whether the water pollutions have dangerous effect on the people and animals in the areas of study environment, prevent all individuals, relevant organizations, researchers from drinking underground water that is very closed to dumping areas in order to avoid deadly diseases, inform the people on the hazard and result of wastes on their health from drinking underground water especially those that are very close to the dumping areas in other …
Is the topic “Poverty and Access to Justice” recommended for Sociology Project?
Yes it is highly recommended — This study was initiated to investigate the relationship between poverty and access to justice in Dutsin-ma local government. Specific objectives of the research are to: identify the spread and availability relative distance of court services; review the trial process and determine its ease and affordability to the citizens; make an assessment of poverty in relation to access to justice; and adopt the measures that will help to improve access to justice. The study adopted the survey research design and the stratified random sampling technique was used in selecting respondents. Questionnaires were used as instrument of data collection and a total of 150 respondents were used as the sample. Findings revealed that the spread and availability of relative distance of court services …
Is the topic “The Impact of Reward System on Organizational Staff Performance” recommended for Business Administration and Management (BAM) Project?
Yes it is highly recommended — The study examined the impact of reward system on organizational staff performance. The study sought to examine the impact of – basic salary, bonuses, promotion, recognition on work performance, job quality, number of tasks completed. The sample of the study comprised of Nigerian Television Authority (NTA). Primary data was used in the study. A structured questionnaire was used to collect necessary data from 100 randomly selected staffs of NTA. The descriptive statistics and the statistical tool employed to test the hypotheses in the study is chi-square and software Statistical Package for Social Sciences (SPSS) were used to analyze the data. Findings of the study indicated that there is significant impact of financial and non-financial reward system on organizational staff performance …
Is the topic “The Impact of Government’s Poverty Reduction Programmes in Niger State” recommended for Political Science Project?
Yes it is highly recommended — This study examined the Impact of Government’s Poverty Reduction Programmes in Suleja Local Government Area, Niger State; A case study of Suleja Local Government area, between 2006 and 2008. The strategy has been to render assistance to the people, thereby alleviating some difficult situations of their lives and at the same time putting similes and adding new hopes to their lives, as against their poor living conditions. The aim of the study is to examine the impact of Government’s Poverty Reduction Programmes in Suleja Local Government Area, Niger State. In achieving this aim, the following specific objectives of this study were set out to investigate the programme on poverty reduction in Suleja Local Government area of Niger State reduced poverty …
Can the material for “Risk in Supply Chain Logistics Constraints on Opportunity in Northern Eastern Nigeria” be used as a guide for Purchasing and Supply (PS) Project?
Yes it can be used — Supply chain management in any organization seeks to ensure that the goods materials are of the right quality, quantity, though at the right price and from the right source and made available for the organization in use at the right time. The study was carried out to examine the Risk in Supply Chain Logistics Constraints on Opportunity in Northern Eastern Nigeria using Limbot Express Logistics as a case study. In achieving this aim, the following specific objectives were laid out to evaluate the risk in supply chain logistics constraints on opportunity, determine the relationship between the risk management and supply chain logistics and investigate the risk factors inhibiting supply chain logistics in Northern Eastern Nigeria. Investigation revealed that most suppliers …
Can the material for “An In-depth Study of Loan Words From English to Hausa Language” be used as a guide for English / Hausa Project?
Yes it can be used — Language borrowing refers to the loaning of words from one language to another. It usually occurs when languages come in contact either physically (English and Hausa) or through writings. The study was carried out to examine the language Item loaned from English to Hausa. In achieving this aim, the following specific objectives were laid out to find the lexical items that language of development equally loaned from Hausa and determine the frequency of language development through language loaning from one language to another. Primary data were collected from the primary source which questionnaire was used as an instrument of data collection while secondary data were sources from textbooks, journals, newspapers and the internet were employed. Data used in this work …