REPORT ON FABRICATION OF FLOW NOZZLE
ABSTRACT
The flow nozzle was constructed based on the dimensions and specifications of the international standard organization (I.S.O) recommendation.
- Throat diameter 42.5mm
- Length converging nozzle 68mm
- Thickness of nozzle 2mm
- Diameter of major axis of ellipse 85mm
- Diameter of minor axis of ellipse 56.6mm
- Diameter of duct pipe 85mm
The absence of this device (Nozzle) has imposed a very big problems to early scientist. This had existed due to the difficulties in measuring fluid flow in channel.
These scientist latter came out with different kinds of nozzle which facilitates measurement. They were convergent, divergent and divergent-convergent nozzle.
Other metering devices include venturi meter orifice meter, weir etc. each of them has different structures and mode of operation.
The constructed electric is attached to an upstream pipe to give a substantial steady flow to the down stream pipe. Fouling and head loss should be minimized likewise eddies formation. Lastly, the same diameter of tube should be used to replace themanometric tube when it got broken. Likewise the fluid should be maintained.
CHAPTER ONE
1.0 Introduction
The study of fluid behaviour is very important in process engineering. It constitutes the study of unit operation. The branch of engineering that deals with the study of fluid is called fluid machines. An understanding of fluids through pipe, pumps and all kind of process equipment and also for the study of heat flow and pressure change. The branches of fluid machines include fluid static and fluid dynamics fluid static treats fluids in the equilibrium state of no shear streets while fluid dynamics deals with position of fluid in motion relative to other part.
A fluid is a substance that foes not permanently resist distortion. An attempt to change the shape of a mass of fluid result inlayers of fluid scliding over one another until a new shape, shear stress exist, the magnitude of it depend on the viscosity of the fluid and rate of sliding but when final shape is reached, all shear stress will have disappeared.
The term flow means volume per unit time at specified temperature and pressure conditions.
It can be measured using positive displacement meter or rate meter. The term fluid is a generalized name given to liquid and gases. Fluid flow or is transported from one place to another by different means either by container gallon, cylinder, tank the related means to the topic at and now is transportation by pipe.
Pile consist of nozzles and ducts through which liquid flow. A nozzle is a mechanism which kinetic energy of fluid is converted and increased in an adiabatic process.
This process accompanies decrease in pressure and change in flow area of the fluid.
The variation in shape and diameter of different part of nozzle effect the flow of fluid nozzle comes in different types, we have divergent nozzles, convergent nozzles and divergent-convergent nozzles.
The rate of flow of fluid in pipe is measured by devices which facilitates the ascertainment of the volume of fluid flowing in a unit time. These devices are collective called flow meter or rate meters.
Flow meters are of different types such as venturi-meter, flow nozzle, orifice meter, rofa meter and weirs these devices are used as choice. All the devices mentioned above facilitates movement of fluid on specified direction, speed and size.
1.1 Scope of the Project
The aim of this project is to construct a flow nozzle capable of conveying fluid (liquid) from one point to the other. The parameter used depict the pressure change, the velocity and quantity of flow is also inclusive. The nozzle should be able to create a pressure drop in moving fluid and give the quanity of fluid that flow through for a given period of time. The nozzle should be capable of satisfying industrial requirement when placed in process plant for fluid supply.
The flow nozzle fabricated was based on the following prescriptions.
- Throat diameter 42.5mm 42.5mm
- Length of converging nozzle 68mm
- The thickness of the nozzle 2mm
- Diameter of ellipse major axis 85mm
- Diameter of ellipse minor axis 56.6mm
- Diameter of the duct (pipe0 85mm
CHAPTER TWO
2.0 Literature Review
2.1 Introduction
The review of relevant literature is the main topic of this chapter. A literature review covers theoretical and methodological contributions to a certain issue in addition to the state of knowledge at the time of writing. It provides information about the state of the art in relation to the subject you are writing about. It examines the body of work on the chosen subject. The literature evaluation in this study comprises the …
Procedure for Downloading the PDF (Docx) Material
Report on Fabrication of Flow Nozzle can be downloaded by requesting the full set of materials at the project or seminar cost. The document will be sent via Microsoft Word (MS-Word) format via WhatsApp (e-mail) following payment confirmation.
| Seminar Material Cost ₦3,000 | Project Material Cost ₦5,000 |
Request Complete Material
 | Click here to request the Complete Material via WhatsApp including;
|
TABLE OF CONTENTSPRELIMINARY PAGES
- Title page
- Approval page
- Dedication
- Acknowledgement
- Table of Contents
- Abstract
- 1.0 Introduction
- 1.1 Scope of the Project
- 2.0 Historical Review of Flow
- 2.1 Theory of Flow Meter
- 2.2 Venturing Meter
- 2.3 Orifice Meter
- 2.4 Flow Nozzle
- 2.5 Types of Flow Nozzle
- 2.6 Characteristics of Flow Nozzle
- 2.7 Advantages of Flow Nozzle
- 2.8 Disadvantages of Flow Nozzle
- 3.0 Material of Construction
- 3.1 Construction
- 4.0 Discussion
- 4.1 Recommendation
- 4.2 Conclusion
- 4.3 REFERENCES
- 4.4 Nomenclature
Disclaimer for Complete Material Utilization
The displayed research work titled "Report on Fabrication of Flow Nozzle" is stated as a research guideline towards accomplishing your assigned project / seminar research work. All the research materials on this website are ONLY for research purposes and should be used as a guideline in developing your research work. For no reason should you copy word for word as projectlist.com.ng will not be liable for any who copied the material. By ordering the complete research guideline, it signifies that you've accepted our terms of service.
PRELIMINARY PAGES
- Title page
- Approval page
- Dedication
- Acknowledgement
- Table of Contents
- Abstract
- 1.0 Introduction
- 1.1 Scope of the Project
- 2.0 Historical Review of Flow
- 2.1 Theory of Flow Meter
- 2.2 Venturing Meter
- 2.3 Orifice Meter
- 2.4 Flow Nozzle
- 2.5 Types of Flow Nozzle
- 2.6 Characteristics of Flow Nozzle
- 2.7 Advantages of Flow Nozzle
- 2.8 Disadvantages of Flow Nozzle
- 3.0 Material of Construction
- 3.1 Construction
- 4.0 Discussion
- 4.1 Recommendation
- 4.2 Conclusion
- 4.3 REFERENCES
- 4.4 Nomenclature
Disclaimer for Complete Material Utilization
The displayed research work titled "Report on Fabrication of Flow Nozzle" is stated as a research guideline towards accomplishing your assigned project / seminar research work. All the research materials on this website are ONLY for research purposes and should be used as a guideline in developing your research work. For no reason should you copy word for word as projectlist.com.ng will not be liable for any who copied the material. By ordering the complete research guideline, it signifies that you've accepted our terms of service.
Frequently Asked Questions (FAQ)
Can the material for “Design and Implementation of a Computerized Seaport Billing System” be used as a guide for Computer Science (CS) Project?
Yes it can be used — Computerized Seaport Billing System is Software designed to handle time and billing tracking as well as invoicing customers for services and products as well as monitoring an individual water transportation bill. It can track the hours worked by employees as well as expenses associated with projects or clients. The aim of this study is to develop a computerized seaport billing system that will handle the bills raised for various customers. In achieving this aim, the following specific objectives were laid out as follows to design and implement an application software that will to provide proper customer fills and records and reduce the amount of time required to prepare a bill by developing an ease and efficient automated system. The motivation …
Can this topic “National Savings and Economic Growth in Nigeria (1980 - 2007)” be used for Economics Project?
Yes it can be utilized for research — The research work studied the national savings and Nigerian economic growth, spanning from 1970-2007. The study adopted Ordinary Least Square (OLS) single equation model. Using time series data over the period, the work shows that National Savings is not significant at SY level and it granger causes real gross domestic product. The study also shows that exchange rate is significant in its contribution to economic growth. The investment as one the of explanatory variables is significant and supports the idea that most of the investments in Nigeria are not from savings. The study also reveals that money supply has no impact on Nigeria’s economic should increase national savings through increased interest rate on deposits and also maintain its managed floating …
Is the topic “Jig-Saw, Buzz Group and Conventional Learning Strategies and Students’ Academic Performance in Basic Science” recommended for Science Education Project?
Yes it is highly recommended — Collaborative learning has several activities, which help to improve students’ learning. The widely used techniques of collaborative learning strategies are Jigsaw, Buzz Groups, and Conventional learning strategies. The aim of the study is to examine the Jig-saw, Buzz Group and Conventional Learning Strategies and Students’ Basic Science Academic Performance in Warri-South district, Delta State. In achieving this aim, the following specific objectives were set out to evaluate the Students’ Academic Performance in Basic Science using Jig-saw, Buzz Group and Conventional Learning Strategies, investigate the effects of Jigsaw based Learning on secondary school students’ achievement in Basic Science, examine the students' academic achievement to Basic Science between male and female students exposed to jigsaw strategy, and examine the impact of jigsaw …
Can the material for “Provisions of Adequate Employment and Regulations for Seafarers in Nigeria” be used as a guide for Marine Engineering Project?
Yes it can be used — The study was carried out to investigate the provisions of adequate employment and regulations for seafarers in Nigeria. In achieving this aim, the following specific objectives were laid out to examine the factors instigating the provisions of adequate employment, evaluate the laid out regulations governing the activities of seafarers and find out if the regulations for seafarers increases the employees’ performance and productivity in Nigerian Ports Authority. The research design used in this report is descriptive design, utilizing questionnaire method to obtain information from the respondents for this project. A total of 200 (two hundred) respondents were selected for this study to represent the entire population of the study. For null hypotheses were formulated and tested using the one-way ANOVA …
Can the material for “Problem and Prospects of Pig Farming” be used as a guide for Agricultural Engineering (AE) Project?
Yes it can be used — The purpose of this study was to investigate problem and prospect of pig farming in Ovia North East Local Government Area of Edo State four research questions formulated and analyzed. The respondents were made up of pig farmers Ovia North East Local Government Area. All the respondents were randomly selected from the three main markets in Ovia North East Local Government Area and seven. One set of instrument was used in collecting data for the study i.e. questionnaires. The data collected from the respondents were analyzed using simple percentages from the analysis of data, the following were the findings. Transportation is one of the problem of pig farming and Finance contribute one of the major problem. …
Can the material for “An Assessment on the Activities of Fraudsters Using ATM Pin” be used as a guide for Criminology and Security Studies Project?
Yes it can be used — Automated Teller Machine frauds are illegalities connected to the businesses and operations on ATMs. This includes acts such as identity theft, pin misplacement, card theft, password hacking and electronic fund transfer. The aim of the study is to assess the Activities of Fraudsters using ATM Pin. In achieving this aim, the following specific objectives were laid out to know the relationship between ATM fraud and fraud, examine the ways by which these frauds are committed, and know the measures that central bank of Nigeria has taken to mitigate this fraud. The research design used in this report is descriptive design, utilizing questionnaire method to obtain information from the respondents for this project. A total of 150 (one hundred and fifty) …
Can this topic “Impact of Leadership Styles on Employee Productivity in Private Organizations in Nigeria” be used for Human Resource Management (HRM) Project?
Yes it can be utilized for research — Leadership style is the way which influence process is exercised. It is the characteristics ways in which the leadership relates to their employees. The study was carried out to examine the Impact of Leadership Styles on Employee Productivity in Private Organizations in Nigeria. In achieving this aim, the following specific objectives were laid out to examine the impact of leadership styles on employee’s productivity and performance and investigate out the factors responsible for the choice of leadership style in Private Organizations. Investigation revealed that leadership styles in the library in supposed to motivate the staff into been productive and perform optimally. The research design used in this report is descriptive design, utilizing questionnaire method to obtain information from the respondents …
Can the material for “Teenage Pregnancy and How It Affects Educational Development of Our Teenagers” be used as a guide for Education Project?
Yes it can be used — The main concern of this study was to final out the teenage pregnancy and how it affects the educational development of our teenagers in Kaura Local Government Area of Kaduna state. The study emphasized on the factor behind teenage pregnancy in the local government. The study revealed that teenage pregnancy is as a result of the following, teenage girls having relationship with older male counterparts, watching pornographic films without adult guidance, giving them out in marriage to prevent them from prostituting inadequate information on sex education. The study indicated that despite the attitudes parents towards teaching of sex education, there were some problems, which need to be seriously looked into by the Kaduna state government, such as the inclusion of sex …
Can the material for “The Role of Organisation Culture on Employee Job Performance” be used as a guide for Industrial Relations and Personnel Management (IRPM) Project?
Yes it can be used — The research was conducted to investigate the Role of Organizational Culture on Employee Job Performance at Dangote Agro Sack Limited. The study adopted survey research method and a sample size of 240 respondents were drawn from the population through simple random sampling technique. Data was generated by’questionnaire administration and the collected data was presented and analyzed with the aid of statistical tools. It was concluded among others that organizational culture has positive effect on workers’ performance which is based on the findings that companies derive core values and beliefs that guide the conduct of her workers in all spheres of business activities. The study recommends that organizational culture and value should be reviewed at appropriate times so as to derive …
Can the material for “Design and Implementation of a Computerized Image Transfer System in a Wide Area Network” be used as a guide for Computer Science (CS) Project?
Yes it can be used — Computer image is the acquisition, processing and display of using computers. The aim of the study is to Design and implement a Computerized Image Transfer System in a Wide Area Network. In achieving this aim, the following specific objectives were laid out to develop an application software that will Enable users to easily host, store and backup image data, with high-performance computing easy to retrieve and make image file available to the end-user at any point in time. The motivation that led to the implementation of the proposed system is that many business firms have not seen it as necessary to embark on internet services. It is usually difficult to transfer images from one place to the other, most especially …