DESIGN AND CONSTRUCTION OF STEP UP TRANSFORMER WITH MULTI OUTPUT
ABSTRACT
Transformer is one of the indispensable devices mostly in Electric Power Transmission, Transformer Step-down or Step-up, the output voltage/current to the design requirement. The study was conducted to design and construct a step up transformer with multi output. This project was meant to show the necessary step and methods of designing and constructing a typical step-up auto transformer with tapping.
In this project, the information utilized was gathered from both primary data (personal interview) and secondary data (information from textbook and internet). The project work consist of copper winding which was self-induced the wind has several tapping for secondary voltages. It also consists of Iron Core which was laminated, bolt and nut to hold the Iron Core tight.
In this design, 1KVA to be 5000w was utilized, for any current that come in like input to give 5000w output for a Air-conditioner to used. The winding determine wealthier step-up or step-down, in step-up is to increase voltage rating the primary turn were determine by measuring the length of the primary coil to the calculated length value then number of turns was 396 turns, which was rounded up to 400 turns for ease of calculation of the secondary number of turns, so secondary was calculating transformer ratio.The significance of this research entails that, transformer initially raises the generated voltage for efficient transmission over long distance and there after decrease the system voltage for local destruction and utilization.
CHAPTER ONE
1.1 Introduction
A transformer is a magnetically coupled coil used in transmission of an electric power. This coil may be electrically link, but not electrically linked as in two winding transformer.
It consists of primary winding and secondary winding which the number of turns varies depending on the type of transformer. Transformers are operated by the principle of mutual inductance between two separate coils wound on the same core.
There is also the step – up and step – down transformer. This work looks into the construction of a step – up auto transformer.
Auto – transformer is the transformer that consists of only one is winding port of the being common to both primary winding and secondary winding.
That theory of an auto transformer and it operation is similar to that of the two winding transformer, it has high efficiency where cheap (because it used less copper) it is applicable where transformer ratio is little differs from unity.
- Standard Wire Guage: These are specific number of a wine (coil) it is used in this project to gauge on 17 which has a diameter of 1.422m.
- Transformer: It is a cutout shape rubber material with a hollow in the center and with grove around is to avoid electrical link between the core and the coil.
- Voltmeter: This is the instrument used to measure the voltage across the circuit. It is connected in parallel to the winding
- Insulator: These are the material used to isolate two conductors from touching each other.
1.2 Aim or Purpose of the Study
The aim of this project is to design and construct a step up transformer with multi output. This transformer is a step – up transformer, it help in stepping up voltage, because of the primary winding function and the secondary winding function from the voltage rating to the normal rating is to step – up voltage in the transformer.
1.3 Objective of the Study
This transformer consists of only one winding part of the common to both primary and secondary winding. It had high efficiency and uses less copper, it is applicable where transformer ratio is differ from unity. The primary winding is connected to the power source and the other winding are secondary winding it help the transformer in increase the voltage to the normal voltage rate.
1.4 Significance of the Study
The R. Fienberg in “Modern Power Transformer Practice” stated that a transformer has a significance rate that transformer machine in bringing down the voltage rate it’s the desire amount.
Transformer initially raises the generated voltage for efficient transmission over long distance and there after decrease the system voltage for local destruction and utilization.
1.5 Lamination
The transformer comprises of ‘E’ and ‘I’ laminated cores which was obtained from a scrub transformer and recycled. The process of recycling involve washing of core with fuel to removed the unwanted grease and then dry up and grease with new oil so as to prevent air gap.
it also comprise of coil which bought fresh one in the market, switches, connector former and insulator to isolate the output and input wires from touching each others.
1.6 Scope of the Study
The scope of this research is focused on the design and construction of step up transformer with multi output.
1.7 Limitations of the Study
During the course of this study, there were some problems encountered which stood as limitations to the research work. Some of the limitations include:
- Time Constraint: The time frame given to accomplish this project was very short due to school academic calendar and it was carried out under pressure which made the researcher not to implement some necessary features.
- Financial Constraint: Insufficient fund tends to impede the efficiency of the researcher in sourcing for the relevant materials, literature or information and in the process of data collection (internet).
1.8 Definitions of Terms
a transformer is a magnetically coupled with coil as in show in fig.1.1, a transformer rescues input current and send output voltage, be it step – up or step – down transformer it used in transmission of an electric power.
Standard Wire Guage:
These are specific number of a wine (coil) it is used in this project to gauge on 17 which has a diagram of 1.422m.
Transformer:
It is a cutout shape rubber material with a hollow in the center and with grove around is to avoid electric link between the core and the coil.
Voltmeter:
This is the instrument used to measure the voltage across the circuit. It is connected in parallel to the winding.
Insulator:
These are the material used to isolate two conductors from touching each other.
Casing:
The outer cover of the transformer this serve is from external hazard was made of metal as earlier stated in our previous chapter.
The Switch:
This is a mechanical advice used to open and close a complete electric circuit. The multipurpose low voltage (AC) transformers are connected via switch to the power supply.
The primary winding is connected to the power source and the other winding are secondary winding
We have step – up transformer and step – down transformer. But in this context emphasis will be lay on the step – up auto transformer.
CHAPTER TWO
2.0 Literature Review
2.1 Introduction
The review of relevant literature is the main topic of this chapter. A literature review covers theoretical and methodological contributions to a certain issue in addition to the state of knowledge at the time of writing. It provides information about the state of the art in relation to the subject you are writing about. It examines the body of work on the chosen subject. The literature evaluation in this study comprises the …
Procedure for Downloading the PDF (Docx) Material
Design and Construction of Step Up Transformer with Multi Output can be downloaded by requesting the full set of materials at the project or seminar cost. The document will be sent via Microsoft Word (MS-Word) format via WhatsApp (e-mail) following payment confirmation.
| Seminar Material Cost ₦3,000 | Project Material Cost ₦5,000 |
Request Complete Material
 | Click here to request the Complete Material via WhatsApp including;
|
TABLE OF CONTENTSPRELIMINARY PAGES
- Title page
- Approval page
- Dedication
- Acknowledgement
- Table of Contents
- Abstract
INTRODUCTION
- 1.1 Introduction
- 1.2 Aim or Purpose of the Study
- 1.3 Objective of the Study
- 1.4 Significance of the Study
- 1.5 Lamination
- 1.6 Scope of the Study
- 1.7 Limitations of the Study
- 1.8 Definitions of Terms
LITERATURE REVIEW
- 2.1 Introduction
- 2.2 Conceptual Review of Transformer
- 2.3 Classification of Transformer
- 2.4 Types of Transformer
- 2.5 Basics Principle of Transformer
- 2.6 Auto – Transformer
- 2.7 Tapped Transformer
MATERIALS AND METHODS
- 3.1 Introduction
- 3.2 List of Component
- 3.3 Circuit Diagram
- 3.4 Winding Procedure
- 3.5 Fixing of Laminating Iron
- 3.6 Block Diagram of the Circuit
- 3.7 Precautions during Construction
RESULTS AND DISCUSSION
- 4.1 Introduction
- 4.2 Working Principal of a Transformer
- 4.2.1 Transformer Ratio
- 4.3 Description of Component
- 4.4 Precaution
- 4.5 Application
- 4.6 Test and Measurement
- 4.7 Material Used and Source
- 4.7.1 Design Procedure of the Transformer
- 4.7.2 Mechanical Design
- 4.7.3 Electrical Design
- 4.8 Bill of Quantity
- 4.9 Specification
- 4.10 Cost Analysis
SUMMARY, CONCLUSION AND RECOMMENDATION
- 5.1 Introduction
- 5.2 Summary of Findings
- 5.3 Conclusion
- 5.4 Recommendation
REFERENCES
Disclaimer for Complete Material Utilization
The displayed research work titled "Design and Construction of Step Up Transformer with Multi Output" is stated as a research guideline towards accomplishing your assigned project / seminar research work. All the research materials on this website are ONLY for research purposes and should be used as a guideline in developing your research work. For no reason should you copy word for word as projectlist.com.ng will not be liable for any who copied the material. By ordering the complete research guideline, it signifies that you've accepted our terms of service.
PRELIMINARY PAGES
- Title page
- Approval page
- Dedication
- Acknowledgement
- Table of Contents
- Abstract
INTRODUCTION
- 1.1 Introduction
- 1.2 Aim or Purpose of the Study
- 1.3 Objective of the Study
- 1.4 Significance of the Study
- 1.5 Lamination
- 1.6 Scope of the Study
- 1.7 Limitations of the Study
- 1.8 Definitions of Terms
LITERATURE REVIEW
- 2.1 Introduction
- 2.2 Conceptual Review of Transformer
- 2.3 Classification of Transformer
- 2.4 Types of Transformer
- 2.5 Basics Principle of Transformer
- 2.6 Auto – Transformer
- 2.7 Tapped Transformer
MATERIALS AND METHODS
- 3.1 Introduction
- 3.2 List of Component
- 3.3 Circuit Diagram
- 3.4 Winding Procedure
- 3.5 Fixing of Laminating Iron
- 3.6 Block Diagram of the Circuit
- 3.7 Precautions during Construction
RESULTS AND DISCUSSION
- 4.1 Introduction
- 4.2 Working Principal of a Transformer
- 4.2.1 Transformer Ratio
- 4.3 Description of Component
- 4.4 Precaution
- 4.5 Application
- 4.6 Test and Measurement
- 4.7 Material Used and Source
- 4.7.1 Design Procedure of the Transformer
- 4.7.2 Mechanical Design
- 4.7.3 Electrical Design
- 4.8 Bill of Quantity
- 4.9 Specification
- 4.10 Cost Analysis
SUMMARY, CONCLUSION AND RECOMMENDATION
- 5.1 Introduction
- 5.2 Summary of Findings
- 5.3 Conclusion
- 5.4 Recommendation
REFERENCES
Disclaimer for Complete Material Utilization
The displayed research work titled "Design and Construction of Step Up Transformer with Multi Output" is stated as a research guideline towards accomplishing your assigned project / seminar research work. All the research materials on this website are ONLY for research purposes and should be used as a guideline in developing your research work. For no reason should you copy word for word as projectlist.com.ng will not be liable for any who copied the material. By ordering the complete research guideline, it signifies that you've accepted our terms of service.
Frequently Asked Questions (FAQ)
Can the material for “The Influence of Effective Personnel Management Practice in Organization Performance” be used as a guide for Personnel Management Project?
Yes it can be used — Effective Personnel Management in simple terms means the act of getting people together to accomplish desired goals. It comprises planning, organizing, Resourcing, leading or directing, and controlling an organization. The study was carried out to examine the influence of effective personnel management practice in organization performance using in Owerri West Local Government Area in Imo State as a case study. In achieving this aim, the following specific objectives were laid out to ascertain basic understanding of the effect of personnel management on organizational performance, elucidate some problems encountered by an organization and ascertain the relationship between personnel management and organizational performance. The research design used in this report is descriptive design, utilizing questionnaire method to obtain information from the respondents …
Can the material for “Gender Issues in Akachi Adimora Ezeigbo’s Trafficked and Zaynab Alkali’s the Virtuous Woman” be used as a guide for English / Igbo Project?
Yes it can be used — This study will be subjected to Akachi and Alkali’s Ideology on gender issues that is enhancement of gender education especially women and women empowerment in the society. Gender is a concept used in social sciences analysis to look at roles and activities of men and women. The focus of gender issues is not on biological differences between men and women but rather on their experiences as member of the society. The main purpose of this study is to examine the reason for women oppression and discrimination in our society and thus encourage the liberation of all women. Feminist perspectives or theories vary just as there are different analysis by feminists about causes of gender problem. However, it must be stated …
Can the material for “Elections and Social Media in Nigeria” be used as a guide for Political Science Project?
Yes it can be used — Elections in Nigeria prior to 2011, were characterized by high level of propaganda, dissemination of fake and uncoordinated information, scarcity of airtime and space for citizen’s participation and other forms of traditional media fostered electoral prejudices. Electorates were at the mercy of the tradition media; Television, Radio, Newspaper, Magazines, etc. to interact with their candidates. The wide gap that existed between the electorates and the candidates denied them their rights to properly asses such candidates before the polls, and in the process, the average class often stayed away from elections, because they believe that their votes never count. With the advent of the social media, following the productive USA social media political usage experience, where then Senator Barack Obama, successfully …
Can the material for “The Effect of Strike on Teachers’ Productivity” be used as a guide for Public Administration (PA) Project?
Yes it can be used — This study looked into the effect of strike action on teachers’ productivity, in the specific interest of Nigeria Union of Teachers Abia State chapter. In carrying out this work, relevant research questions on hypothesis were given as reading assumptions, relevant literature were reviewed with the aim of authenticating the issue under study. The researcher used survey designed for the project layout on respondents for data collection (questionnaire). The responds of the respondents are analyzed using table and percentage for the test of hypothesis. Actually, the result of the finding showed that strike is inevitable in their organization. This is true because it aims at achieving workers demand from the management so as to promote and defend their employment and ensuring job security. …
Can the material for “Response of Maize (Zea Mays L) and Some Soil Physical and Chemical Properties to Poultry Manures and Tillage Practices in an Ultisol” be used as a guide for Agricultural Engineering (AE) Project?
Yes it can be used — A field trial was conducted to assess the response of maize and soil physical and chemical properties to the different tillage practices and poultry manure levels in an Ultisol in National Institute for Oil Palm Research Institute, Edo State between September to November, 2014. The field trial was laid out as a two by three factorial experiment in a completely randomized design. Four replicates and treatment combinations formed the main plot treatments (till and no-till) and poultry manure was assigned to the subplot. Sub plot treatments were three poultry manure levels; control (no poultry manure), 4 kg/ha and 8 kg/ha. Tillage treatments included till and no till. Results from the study showed that tillage and manure interaction did not show any significant …
Can the material for “The Impact of Staff Training and Development in Tertiary Institutions” be used as a guide for Public Administration (PA) Project?
Yes it can be used — This research work is poised to look into the Impact of Staff Training and Development in Tertiary Institutions (A Case Study of Kogi State University, Anyigba) The study is aimed at examining the Impact training and development has on the staff of tertiary institutions in the country particularly on Kogi State University, Anyigba, as well as reviewing relevant literatures on the types of training, training responsibility, training and development needs, evaluation of training and the benefits training has on staff development. The researcher used both primary and secondary sources of data. In analyzing the data, the use of simple percentage method was adopted for easy understanding. It was revealed after the. After review and updating various works written by different …
Can the material for “Application of Geoelectrical Resistivity Imaging to Investigate Groundwater Potential” be used as a guide for Physics Project?
Yes it can be used — The study was conducted to determine the Application of Geoelectrical Resistivity Imaging and investigate the Groundwater Potential in the area under study. In achieving this aim, the following specific objectives were laid out to determine the availability of groundwater resources in Atan using geoelectrical resistivity method and determine the depth of groundwater of the study area using vertical electrical sounding. Geoelectrical resistivity imaging using both 2D and Vertical Electrical Sounding (1D) method was carried out in Atan, Ado/Odo Ota Local Government, Ogun State ,Nigeria using the PAS earth resistivity meter. Three profiles was carried out using both Wenner and Schlumberger array configuration. The data was interpreted using RES2DINV for 2D and computer iteration method (WinResist) for VES. Results showed that …
Can the material for “Impacts of Christianity” be used as a guide for Philosophy Project?
Yes it can be used — Christianity as a religion has affected all spheres of life among the people of Nigeria. A careful study of the religious background of the Nnewi people will show that Christianity has found its way into both the urban and rural areas of the Nnewi society. This study is aimed at looking into the relevance of Christianity in the development of the Nnewi nation. For better understanding of the project, a brief introduction to the lifestyle of the Nnewi people prior to the advent of Christianity will also be made. The division of work for this study is as follows:-1 General background study via the aims, methodology and clarification of terms.2 The historical origin and organizational lifestyle of the Nnewi people. …
Can the material for “The Study of Motivation on Employee Performance” be used as a guide for Business Administration and Management (BAM) Project?
Yes it can be used — The project focuses on the impact of motivation on employee’s performance, a study of Suleja local government administration. This project is important because it will expose the positive results of motivating employees in an organization, and be an eye opener to entrepreneur. Data was collected and analyzed by use of questionnaire and simple percentages. The findings amongst other ones are as follows. That the workers of Suleja local government administration are not efficient, there is idleness and absenteeism and lateness to work which has significant impact on their productivity. It was found out that there is poor or inadequate motivation; this affects the moral of the employees. Based upon the finding the researcher recommends as follows. The management should create …
Can this topic “The Use of Information and Communication Technology to Effect Service Delivery by Banks in Nigeria” be used for Banking and Finance (BF) Project?
Yes it can be utilized for research — This research was carried out to examine the effective service delivery by banks in Nigeria through the use of (ICT). There have been series of assumption that the use of information and communication technology has greatly enhanced the output of the banking sector in Nigeria. It is in a bid to confirm these assumptions that the researcher carried out this study. Questionnaire was the instrument used to collect data from respondents with a sample size of one hundred staffs from various banks in Nigeria, information was also sought from textbooks and journals based on the analysis of data, it was revealed that the use of information and communication technology has really enhanced the effective service delivery in the banking sector. …