CONSTRUCTION OF 1000W INVERTER WITH SOLAR PANEL
ABSTRACT
The project 1000 watts inverter with solar panel is a circuit that is divided in to two parts, (a) the inverter convert or invert the input signal from the power supply (dc) into ac power, inverter comprises of three stage, the oscillator, drivers and the power transistors, the oscillator is also known as the signal generator which convert the input voltage from a dc to an alternating wave, the driver amplifier or drive the incoming signal from the oscillator while the power transistor powers the transformer to generate a high ac voltage at the output, (b) the solar panel convert the energy from the sun light into voltage which is used to charge the battery.
CHAPTER ONE
1.0 Introduction
An inverter is an electrical device that converts direct current (DC) to alternating current (AC); the converted AC can be at any required voltage and frequency with the use of appropriate transformers, switching, and control circuits. An inverter is essentially the opposite of a rectifier.
Static inverters have no moving parts and are used in a wide range of applications, from small switching power supplies in computers, to large electric utility high-voltage direct current applications that transport bulk power. Inverters are commonly used to supply AC power from DC sources such as solar panels or batteries.
The electrical inverter is a high-power electronic oscillator. It is so named because early mechanical AC to DC converters was made to work in reverse, and thus was “inverted”, to convert DC to AC.
An inverter converts the DC electricity from sources such as batteries, solar panels, or fuel cells to AC electricity. The electricity can be at any required voltage; in particular it can operate AC equipment designed for mains operation, or rectified to produce DC at any desired voltage.
Grid tie inverters can feed energy back into the distribution network because they produce alternating current with the same wave shape and frequency as supplied by the distribution system. They can also switch off automatically in the event of a blackout.
Micro-inverters convert direct current from individual solar panels into alternating current for the electric grid.
1.0 Uninterruptible Power Supplies
An uninterruptible power supply (UPS) uses batteries and an inverter to supply AC power when main power is not available. When main power is restored, a rectifier is used to supply DC power to recharge the batteries.
1.1 Induction Heating
Inverters convert low frequency main AC power to a higher frequency for use in induction heating. To do this, AC power is first rectified to provide DC power. The inverter then changes the DC power to high frequency AC power.
1.2 HVDC Power Transmission
With HVDC power transmission, AC power is rectified and high voltage DC power is transmitted to another location. At the receiving location, an inverter in a static inverter plant converts the power back to AC.
1.3 Variable-Frequency Drives
Main article: variable-frequency drive
A variable-frequency drive controls the operating speed of an AC motor by controlling the frequency and voltage of the power supplied to the motor. An inverter provides the controlled power. In most cases, the variable-frequency drive includes a rectifier so that DC power for the inverter can be provided from main AC power. Since an inverter is the key component, variable-frequency drives are sometimes called inverter drives or just inverters.
1.4 Electric Vehicle Drives
Adjustable speed motor control inverters are currently used to power the traction motors in some electric and diesel-electric rail vehicles as well as some battery electric vehicles and hybrid electric highway vehicles such as the Toyota Prius. Various improvements in inverter technology are being developed specifically for electric vehicle applications. In vehicles with regenerative braking, the inverter also takes power from the motor (now acting as a generator) and stores it in the batteries.
1.5 Air Conditioning
Main article: Inverter (air conditioning)
An air conditioner bearing the inverter tag uses a variable-frequency drive to control the speed of the motor and thus the compressor.
1.6 The General Case
A transformer allows AC power to be converted to any desired voltage, but at the same frequency. Inverters, plus rectifiers for DC, can be designed to convert from any voltage, AC or DC, to any other voltage, also AC or DC, at any desired frequency. The output power can never exceed the input power, but efficiencies can be high, with a small proportion of the power dissipated as waste heat.
CHAPTER TWO
2.0 Literature Review
2.1 Introduction
The review of relevant literature is the main topic of this chapter. A literature review covers theoretical and methodological contributions to a certain issue in addition to the state of knowledge at the time of writing. It provides information about the state of the art in relation to the subject you are writing about. It examines the body of work on the chosen subject. The literature evaluation in this study comprises the …
Procedure for Downloading the PDF (Docx) Material
Construction of 1000W Inverter with Solar Panel can be downloaded by requesting the full set of materials at the project or seminar cost. The document will be sent via Microsoft Word (MS-Word) format via WhatsApp (e-mail) following payment confirmation.
| Seminar Material Cost ₦3,000 | Project Material Cost ₦5,000 |
Request Complete Material
 | Click here to request the Complete Material via WhatsApp including;
|
TABLE OF CONTENTSPRELIMINARY PAGES
- Title page
- Approval page
- Dedication
- Acknowledgement
- Table of Contents
- Abstract
- Introduction
- 1.0 Uninterruptible power supplies
- 1.1 Induction heating
- 1.2 HVDC power transmission
- 1.3 Variable – frequency drives
- 1.4 Electric vehicle drives
- 1.5 Inverter (Air – Condition)
- 1.6 The general case
- 2.0 literature review
- 3.0 Components used and their functions
- 3.1 Microcontroller
- 3.2 Basics of microcontrollers
- 3.3 Programming the peripherals interface controller (PIC) 16F84
- 3.4 Crystal oscillator
- 3.5 Relay
- 3.6 Voltage regulator
- 3.7 Transformers
- 3.8 Capacitor
- 3.9 Resistors
- 3.10 Diodes
- 3.11 Switches
- 4.0 Construction / Operation
- 4.1 Construction
- 4.2 Circuit diagram
- 4.3 Programming the microcontroller
- 4.4 Procedure for programming devices
- 5.0 Conclusion
- 5.1 Summary of problem encountered
- Recommendation
REFERENCES
Disclaimer for Complete Material Utilization
The displayed research work titled "Construction of 1000W Inverter with Solar Panel" is stated as a research guideline towards accomplishing your assigned project / seminar research work. All the research materials on this website are ONLY for research purposes and should be used as a guideline in developing your research work. For no reason should you copy word for word as projectlist.com.ng will not be liable for any who copied the material. By ordering the complete research guideline, it signifies that you've accepted our terms of service.
PRELIMINARY PAGES
- Title page
- Approval page
- Dedication
- Acknowledgement
- Table of Contents
- Abstract
- Introduction
- 1.0 Uninterruptible power supplies
- 1.1 Induction heating
- 1.2 HVDC power transmission
- 1.3 Variable – frequency drives
- 1.4 Electric vehicle drives
- 1.5 Inverter (Air – Condition)
- 1.6 The general case
- 2.0 literature review
- 3.0 Components used and their functions
- 3.1 Microcontroller
- 3.2 Basics of microcontrollers
- 3.3 Programming the peripherals interface controller (PIC) 16F84
- 3.4 Crystal oscillator
- 3.5 Relay
- 3.6 Voltage regulator
- 3.7 Transformers
- 3.8 Capacitor
- 3.9 Resistors
- 3.10 Diodes
- 3.11 Switches
- 4.0 Construction / Operation
- 4.1 Construction
- 4.2 Circuit diagram
- 4.3 Programming the microcontroller
- 4.4 Procedure for programming devices
- 5.0 Conclusion
- 5.1 Summary of problem encountered
- Recommendation
REFERENCES
Disclaimer for Complete Material Utilization
The displayed research work titled "Construction of 1000W Inverter with Solar Panel" is stated as a research guideline towards accomplishing your assigned project / seminar research work. All the research materials on this website are ONLY for research purposes and should be used as a guideline in developing your research work. For no reason should you copy word for word as projectlist.com.ng will not be liable for any who copied the material. By ordering the complete research guideline, it signifies that you've accepted our terms of service.
Frequently Asked Questions (FAQ)
Can this topic “Production of Alkyd Resin Using Water Melon Seed Oil (Citrullus Lanatus)” be used for Science Laboratory Technology (SLT) Project?
Yes it can be utilized for research — Alkyd resin was prepared using the seed oil of water melon (Citrullus Lanatus). The extraction of the seed oil of Citrullus Lanatus was done by solvent extraction method using n-hexane as the solvent. The physicochemical properties of the oil were determined using standard analytical procedures, the result of the physicochemical properties of the oil is as follows; colour (yellow), specific gravity (0.9), saponification value (181mg KOH g-1). Iodine value (68.63g of iodine/10g of oil), Refractive index at 400C (1.45), Acid value (0.81mg KOH/g) and free fatty acid (12.1mg KOH/g). The result of the physicochemical properties of the oil revealed that the oil is a drying oil since its iodine value is less than 100. The percentage yield of alkyd resin based …
Can the material for “Inventory Control Efficiency in a Manufacturing Company” be used as a guide for Sociology Project?
Yes it can be used — This study examines the essence of effective inventories control and management to manufacturing companies with particular emphasis on Ama Greenfield Breweries plc. The aim of this study is to investigate and ascertain areas of lapses by the company and offer effective ways and solutions in which the manufacturing company can explore the services of inventory management to effect its objectives. In carrying out this study, various research instruments such as questionnaires and oral interview were used to collect data from respondents and a research design was adopted with a sample size of 52. The statistical tool used for this work is Chi-square. Based on the analysis, it was discovered that inventory management plays a vital role in the manufacturing company. A …
Can the material for “The Influence of Guidance and Counselling Services on Academic Achievement and Transition Rate” be used as a guide for Education Project?
Yes it can be used — This study investigated the influence of guidance and counselling services on academic achievement and transition rate of Taraba state students into tertiary institutions. Four research questions answered, using mean and standard deviation, and three null hypotheses tested at 0.05 level of significance using t-test statistics and chi-square guided the study. Population of the study was 1,800 SSIII students in Wukari and Donga education zones of Taraba state. The sample size was 364 students drawn through simple random sampling technique. The study adopted an ex-post-facto research design. The instrument for data collection were students WAEC result to answer research questions 2 − 4 and a structured questionnaire developed by the researcher which was validated by three experts from the faculty of education, …
Can this topic “Attitude of Student Nurses toward People with Disabilities” be used for Nursing (Science) Project?
Yes it can be utilized for research — Disability is a common health issue in both developed and developing countries. The study was carried out to explore the Attitude of Student Nurses toward People with Disabilities. In achieving this aim, the following specific objectives were laid out to investigate the attitude of nursing students towards people with disabilities and demographic variables that influences this attitude and examine the factors instigating the attitude of student nurses toward people with disabilities. Investigation revealed that the problem of poor academic performance among students has become an issue of concern to education stakeholders. Parents spend their hard earned money despite the difficult economic situation to see that their children are given quality education. The research design used in this report is descriptive …
Can the material for “The Role of Budgetary Control as a Tool for Cost Control in Manufacturing Companies in Nigeria” be used as a guide for Accountancy / Accounting Project?
Yes it can be used — The study examined the role of budgetary control as a tool for cost control in manufacturing companies in Nigeria. The study sought to examine the impact of budgetary control on cost control. The sample of the study comprised of ten manufacturing firms registered with Nigeria Stock Exchange (NSE) namely Nestle Nigeria Plc, Unilever Nigeria Plc, Evans Medical Plc, Beta Glass Plc, 7-UP Bottling Company Plc, Nigeria Breweries Plc, Nigeria Flower Mills Plc, Dangote Group, Pz Cussons, Glaxosmithkline. A structured questionnaire was used, and the study adopted both the purposive sampling and simple random sampling technique to select190 randomly selected staff of the manufacturing firms, the study further employed the descriptive survey design and the ex-post facto design. The descriptive statistics and regression …
Can the material for “The Need for Guidance and Counseling Services Among Nigeria University Students” be used as a guide for Guidance and Counselling Project?
Yes it can be used — Guidance and counseling is a practice that had been in existence for a long time and had been passed on from one generation to another. The study was carried out to examine the Need for Guidance and Counseling Services among Nigeria University Students. In achieving this aim, the following specific objectives were laid out to establish the approaches used in guidance and counseling in solving University students disciplinary problems in Nigeria and determine the factors that hinder effective guidance and counseling of University Students in Nigeria. Provision of guidance and counselling services is one of the educational policies of the federal government to cater for the apparent ignorance of many young people about career prospects and personality maladjustment among Nigeria …
Is the topic “Web Based Examination Supervision Scheduling for a Higher Education Institution” recommended for Computer Science (CS) Project?
Yes it is highly recommended — This project aims at automating the examination supervision scheduling of the institute of management and technology, Enugu. An in-dept study made on the existing system of the case study and it’s automation cannot be over emphasized result showed that the existing manual system in use was inadequate in many ways ranging from time wasted and labour lost to waster of funds. Therefore, a need for automation is eminent to effect reduction in these wastes of resources. This work outlines are emphasizing on how information concerning exams supervision scheduling in IMT can be collected processed and stored using the computer system. When this is invented and implemented will in turn help to reduce to a great extent the stress and errors usually encountered during …
Can the material for “Design and Implementation of Users Application Software for Real Estate Management Practice” be used as a guide for Computer Science (CS) Project?
Yes it can be used — This study was carried out to appraise the role of design and implementation of users application software for estate management or real estate practice, it is obvious that the society cannot exist without land, which is the bases for estate practice, and among the four factors of production, land is the most important, because every other factors exist on land. In chapter one of this study, we are going to look at the introduction of estate management or real estate practice, while chapter two, which is literature review will deal with the concept of estate management, types of real estate, Nigerians real estate sector and government control mortgages in estate management and the problem of Nigerian estate management development. Chapter …
Can this topic “Design and Implementation of an Electronic Inventory Invoicing System” be used for Computer Science (CS) Project?
Yes it can be utilized for research — In the course of the project research, the design and implementation of a Computerized Invoicing System was Studies. The rapid increase in information technology have substituted the primitive system of invoicing. This advancement have helped in invoice updating since certain mistakes like sales calculation, alterations and irregular writings of clerks can now be avoided. Personal Computers (PC) can now be used to call-up Charts, table and figures of various kinds to obtains an instant reading on the sales. This work reveals the millennium mechanism through which information could be stored modified and recalled instantly and accurately. If unavoidably includes the development of sales processing and information in business transactions. Analytical method involved invoice input analysis of computerized invoicing system used in Bubbles …
Can this topic “The Banking Industry in Nigeria” be used for Banking and Finance (BF) Project?
Yes it can be utilized for research — Fraud is an awful phenomenon, which like a vein has invaded Nigeria banking industries and the society in general, and puts any organization that it comes into in a distress point or in a state of liquidation. This study highlights the nature and various types of fraud in banks, effects of ban fraud and control measures adopted by management to check fraud incidents. Frauds in the banking system should as much as possible be minimized as it kills the bank and destroys the economy of a nation. Finally, the research work adduced that continuous vigilance should be the watch work if fraudulent practices are to be reduced and possibly eliminated in banking industry. Proposal Impact Of Frauds In The Banking Industry In Nigeria Frauds in …