AUTOMATIC AUTOMOBILE BRAKE FAILURE INDICATOR WITH BUZZER
ABSTRACT
Brake failure indicator circuit is a circuit that constantly monitors the condition of brake. The study was conducted to design and construct an Automatic Automobile Brake Failure Indicator with Buzzer. Investigation revealed that accidents are occurring due to lot of reasons, the one of the main reason is brake failure, it caused to due to poor maintenance, improper use and product defect, in order to safe guard the valuable human for accident the accident monitoring of brake is very important issue in automobile. To meet the need of exploding population economic and effective control of machines is necessary. The brake pressure transducer of an automobile is placed on the brake kit assembly. The sensor is connected to the controlling unit, the output of the controlling unit is connected with the alarm and IVRS, when a pressure of the brake reduced from specified level alarm will gives a danger signal and control system will immediately stop the engine in gear so vehicle will safe from the accident. The result of the findings will be significant in providing a smooth ride for the motorist and when the brake is applied in order to slow down or to stop the vehicle the green LED blinks and the buzzer beeps for about one second if the brake system is accurate and working properly. If brake system fails the red LED glows and the buzzer do not beep when the brakes are applied. Based on the findings, the research recommended that the brake system should be inspected with each oil change or at minimum every 6 months or about every 6,000 miles.
CHAPTER ONE
1.1 Introduction
Brake failure indicator circuit is a circuit that constantly monitors the condition of brake. The sensor which is attached to the circuit get the chance of a brake failure by monitoring the brake switch and reminds an individual of the condition of brake every time when the brake is applied. Most vehicles retain some degree of control over the brakes even if the main system doesn’t work and most vehicles have two braking systems. Today, Machines are widely controlled by automated control system. To meet the need of growing population economic, effective and reliable control of machines as well as their control system is necessary. One acting as backup system even though brake failure is relatively rare along with tire blowouts, brake failure is actually one of the top causes of accidents involving trucks and larger vehicles. The most common cause is that there is a leak in the brake line, master cylinders or wheel cylinders.
As a prelude to other parts of this study, this chapter will discuss the background upon which this study was initiated, the statement of problems that led to this study, the Aim and Objectives of the study. Others are Significance of the study, Scope of work, Limitation of the study and Definition of terms.
1.2 Background of Study
Over the years, machines are now commonly operated by automated control systems. To fulfill the needs of a rising population, inexpensive, effective, and dependable control of machines and their control systems is required. A break failure indicator is a safety feature in vehicles that alerts the driver when there is a problem with the braking system. This warning system is designed to prevent accidents by providing an early warning to the driver that the brakes are not functioning correctly. The break failure indicator typically consists of a warning light on the dashboard that illuminates when there is a problem with the brakes. The braking system is one of the most critical safety features of any vehicle, and it is essential to ensure that it is functioning correctly.
Brake failure can occur due to a variety of reasons, such as worn brake pads, leaky brake lines, or a malfunctioning brake booster. If not detected early, brake failure can lead to serious accidents, injuries, and even fatalities. By having a break failure indicator, drivers can quickly identify any issues with the brakes and take appropriate action to prevent accidents. It is crucial to address any brake problems as soon as possible by taking the vehicle to a qualified mechanic or automotive service center to ensure that the braking system is functioning correctly.
Though the world is getting modernized, we have to face so many problems. One of such problems is accidents. One of the things that everyone tried to avoid is while traveling is accidents, and sometimes it is inevitable.
Now- a-days we can see accidents in every nook and corner of the world. It results in the death of thousands of lives. With the population ever climbing there are more vehicles than ever on road, which means there is a higher livelihood of the brakes giving out.
In foreign countries they take remedial measures for the prevention of accidents but our country like India takes less action against the prevention of accidents. One common cause for accidents is brake failure. Accidents may occur due to brake failure. In such a situation my project brake failure indicator plays an important role in controlling accidents.
All of these things can cause the brake failure. In order to solve this problem, the researcher chooses the ‘Brake failure indicator’ as my project. There are many precautions that should be undertaken while using a vehicle. The brake failure indicator circuit is a combination of various products like LED, piezo buzzer, sensor etc and it is capable to avoid accidents. This is the major benefit of this project. Since it works automatically, it is very easy to use.
Even though the existing products are capable to indicate accidents, but it can only indicate brake failure or failure of electric circuit, when the brake is applied. But my product senses the chance of brake failure by monitoring the brake switch and reminds you of the condition of brake every time, when the brake is applied. Several specific issues can help contribute to brake failure. Some problems include hydraulic lines not being attached properly and overheating brakes, which can damage brake pads or rotors. If individuals are traveling in a vehicle in the state of Connecticut and got in an accident contact a Connecticut vehicle accident lawyer to being prosecuting whoever was responsible. when the driver brakes they are actually pushing a plunger into the master cylinder, which in turn pushes brake fluid through tubes and hoses to brake all the moving units in the vehicle.
Therefore, in Nigeria where the research was carried out, the activities that was conducted is to construct an Automatic Automobile Brake Failure Indicator with Buzzer.
1.3 Statement of Problems
Investigation revealed that accidents are occurring due to lot of reasons, the one of the main reason is brake failure, it caused to due to poor maintenance, improper use and product defect, in order to safe guard the valuable human for accident the accident monitoring of brake is very important issue in automobile.
Also, according to Ashwini et al. (2022), the common braking is not sufficient for avoidance of accidents when driver is not active. Further enhancement has to be done in braking system in order to stop a car or any vehicle when driver is not able to brake. Thus, it needs automatic braking system. This automatic braking system allows the vehicle to brake without support of the driver (Ashwini et al., 2022).
1.4 Aim and Objectives of Study
The aim of the study is to design and construct an Automatic Automobile Brake Failure Indicator with Buzzer. In achieving this aim, the following specific objectives were laid out as follows to construct an automobile braking system that will:
- Continuously monitor the braking system at each and every time during the operation of the vehicle;
- Avoid small number of accidents involving trains and boats caused by brake failure;
- Indicate the failure of brake switch and identify whether the brake is functioning;
- Measure the change in hydrolytic pressure and fluid leakage; and
- Connect the audio visual indicator with a sensor and measure the fluid breaking pressure.
1.5 Significance of Study
The result of the findings will be significant in providing a smooth ride for the motorist and when the brake is applied in order to slow down or to stop the vehicle the green LED blinks and the piezo buzzer beeps for about one second if the brake system is accurate and working properly. If brake system fails the red LED glows and the buzzer do not beep when the brakes are applied.
This study will be of immense benefit to other researchers who intend to know more on this study and can also be used by non-researchers to build more on their research work. This study contributes to knowledge and could serve as a guide for other study.
1.6 Scope of Study
The scope of the research is focused on design and construction of an Automatic Automobile Brake Failure Indicator with Buzzer.
1.7 Limitations of the Study
During the course of this study, many things militated against its completion, some of which are:
- Time Constraint: The time frame given to accomplish this project was very short due to school academic calendar and it was carried out under pressure which made the researcher not to implement some necessary features.
- Research material: availability of research material is a major setback to the scope of the study.
- Frequent power failure: This made the researcher append more money on fuel to ensure sustainable power.
- Financial Constraint: Insufficient fund tends to impede the efficiency of the researcher in sourcing for the relevant materials, literature or information and in the process of data collection (internet).
CHAPTER TWO
2.0 Literature Review
2.1 Introduction
The review of relevant literature is the main topic of this chapter. A literature review covers theoretical and methodological contributions to a certain issue in addition to the state of knowledge at the time of writing. It provides information about the state of the art in relation to the subject you are writing about. It examines the body of work on the chosen subject. The literature evaluation in this study comprises the …
Procedure for Downloading the PDF (Docx) Material
Automatic Automobile Brake Failure Indicator with Buzzer can be downloaded by requesting the full set of materials at the project or seminar cost. The document will be sent via Microsoft Word (MS-Word) format via WhatsApp (e-mail) following payment confirmation.
| Seminar Material Cost ₦3,000 | Project Material Cost ₦5,000 |
Request Complete Material
 | Click here to request the Complete Material via WhatsApp including;
|
TABLE OF CONTENTSPRELIMINARY PAGES
- Title page
- Approval page
- Dedication
- Acknowledgement
- Table of Contents
- Abstract
INTRODUCTION
- 1.1 Introduction
- 1.2 Background of Study
- 1.3 Statement of Problems
- 1.4 Aim and Objectives of Study
- 1.5 Significance of Study
- 1.6 Scope of Study
- 1.7 Limitations of the Study
LITERATURE REVIEW
- 2.1 Introduction
- 2.2 Conceptual Review of Automobile Braking System
- 2.3 Causes of Automobile Brake Failure
- 2.4 Overview of Motor Vehicle Brake Failure and Engine Overheating
- 2.5 Existing Braking System Speed Testing Procedure
- 2.6 Advantages and Disadvantages of the Proposed System
- 2.7 Review of Related Literature
MATERIALS AND METHODS
- 3.1 Introduction
- 3.2 Components Used
- 3.3 Description of Utilized Components
- 3.4 System Operation
- 3.5 Block Diagram of Brake Failure Indicator
- 3.6 Circuit Diagram and Description
TESTING AND RESULTS
- 4.1 Introduction
- 4.2 Construction Procedure and Testing
- 4.3 Installation of the Complete Design
- 4.4 Design Calculation
- 4.5 Assembling of Sections
- 4.6 Testing of System Operation
- 4.7 Bill of Engineering Measurement and Evaluation
SUMMARY, CONCLUSION AND RECOMMENDATION
- 5.1 Introduction
- 5.2 Summary of Findings
- 5.3 Conclusion
- 5.4 Recommendation
REFERENCES
Disclaimer for Complete Material Utilization
The displayed research work titled "Automatic Automobile Brake Failure Indicator with Buzzer" is stated as a research guideline towards accomplishing your assigned project / seminar research work. All the research materials on this website are ONLY for research purposes and should be used as a guideline in developing your research work. For no reason should you copy word for word as projectlist.com.ng will not be liable for any who copied the material. By ordering the complete research guideline, it signifies that you've accepted our terms of service.
PRELIMINARY PAGES
- Title page
- Approval page
- Dedication
- Acknowledgement
- Table of Contents
- Abstract
INTRODUCTION
- 1.1 Introduction
- 1.2 Background of Study
- 1.3 Statement of Problems
- 1.4 Aim and Objectives of Study
- 1.5 Significance of Study
- 1.6 Scope of Study
- 1.7 Limitations of the Study
LITERATURE REVIEW
- 2.1 Introduction
- 2.2 Conceptual Review of Automobile Braking System
- 2.3 Causes of Automobile Brake Failure
- 2.4 Overview of Motor Vehicle Brake Failure and Engine Overheating
- 2.5 Existing Braking System Speed Testing Procedure
- 2.6 Advantages and Disadvantages of the Proposed System
- 2.7 Review of Related Literature
MATERIALS AND METHODS
- 3.1 Introduction
- 3.2 Components Used
- 3.3 Description of Utilized Components
- 3.4 System Operation
- 3.5 Block Diagram of Brake Failure Indicator
- 3.6 Circuit Diagram and Description
TESTING AND RESULTS
- 4.1 Introduction
- 4.2 Construction Procedure and Testing
- 4.3 Installation of the Complete Design
- 4.4 Design Calculation
- 4.5 Assembling of Sections
- 4.6 Testing of System Operation
- 4.7 Bill of Engineering Measurement and Evaluation
SUMMARY, CONCLUSION AND RECOMMENDATION
- 5.1 Introduction
- 5.2 Summary of Findings
- 5.3 Conclusion
- 5.4 Recommendation
REFERENCES
Disclaimer for Complete Material Utilization
The displayed research work titled "Automatic Automobile Brake Failure Indicator with Buzzer" is stated as a research guideline towards accomplishing your assigned project / seminar research work. All the research materials on this website are ONLY for research purposes and should be used as a guideline in developing your research work. For no reason should you copy word for word as projectlist.com.ng will not be liable for any who copied the material. By ordering the complete research guideline, it signifies that you've accepted our terms of service.
Frequently Asked Questions (FAQ)
Can this topic “Design and Implementation of a Online Voter Registration System” be used for Computer Science (CS) Project?
Yes it can be utilized for research — Voting is a very important process in the Nigerian political system. It is one of the means and the most effective method of ensuring a legitimate government through popular participation. To enthrone sound democracy and stability in the political system of Enugu state, a system of refigure voting has to be put in place. The system would among other functions discourage double voting, forging or hoarding of electoral papers, massive transfer of ballot papers destruction of ballot boxes, inflation of election figures and unnecessary delay in pronouncement of election results. This could be achieved by computerized voting process to remove the difficult administrative tasks of the conduct of election in Enugu state. It is the basic forms we set to …
Can the material for “An Assessment of Methods of Teaching Computer Courses to Computer Science Students” be used as a guide for Education Project?
Yes it can be used — The study focuses on the methods of teaching computer courses to computer science major in selected Nigeria polytechnics. It examines the background, methods of teaching, tools and equipments use in teaching computer courses to computer science major. The primary data for the study were generated from well structured question broadcasted to random samples of 70 out of 200 NDII students from federal polytechnic Nekede and Abia State Polytechnic and supported with interviews. Frequency labels, simple proportion percentage ratios, average, ranking, and chi-square (test for goodness of fit) for validation of the some of the some of the findings as distributed. From the data presented and analyzed textbook is the mostly used tool for teaching computer courses to computer science major. …
Can the material for “The Impact of Political Influence on Education” be used as a guide for Political Science Education Project?
Yes it can be used — Political influence on education refers to the success of good educational policies issued by the government on the citizen, as formulation of policies are sometimes influence by the political parties in power which sometimes being criticize by the opposition party. The study was carried out to examine the Impact of Political Influence on Education. In achieving this aim, the following specific objectives were laid out to discover the effects of politics on the implementation of education policy in Nigeria and find out the impact of politics on academic performance of Nigeria students. Investigation revealed that education plays vital role in any community, communities are guided by laws and order, shaping and molding issues on education that are formulated through educational …
Can this topic “Public Relation and It’s Impact in the Banking Industry” be used for Banking and Finance (BF) Project?
Yes it can be utilized for research — The study based on public relation and it’s impact in the banking industry (a case study of GTbank Kaduna branch). The study adopted survey research method using questionnaire as the instrument for gathering data. In writing this project, the research begin with a general introduction of the subject matter, statement of the general problem, as related to the organization rationale or objectives of the study, the scope of the study, limitations of the study and definition of terms. Review of related literature of the scholars are also highlighted in notable areas. Other areas of interested study include the methodology of the entire research work, this include methods or approaches used, instrument used, research population and sample size, sampling procedure employed, …
Can this topic “The Impact of Conflict Management on Organisation Productivity” be used for Public Administration (PA) Project?
Yes it can be utilized for research — Conflict management is a skill any organization requires, as no organizations actually exist without the existence of conflict. The study was carried to investigate the impact of conflict management on organisation productivity using Seven-Up Bottling Company as a case study. In achieving this aim, the following specific objectives were laid out to examine the impact of conflict on organizational productivity, find the means of managing conflict with the organization and emphasized the relationship between conflict and the organizational productivity. The research design used in this report is descriptive design, utilizing questionnaire method to obtain information from the respondents for this project. A total of 150 (one hundred and fifty) respondents were selected for this study to represent the entire population …
Can this topic “Value Added Tax: An Important Source of Revenue to the Government in Nigeria” be used for Accountancy / Accounting Project?
Yes it can be utilized for research — The research work is carried out specifically to appreciate value Added Tax as an important source of revenue to the government in Nigeria and its importance to the development of business organisation. The research work analyse the purpose, problems, significance and also the questions relating to the importance of value Added Tax as a source of revenue to the government in Nigeria. In view of this, the research work is discussed under five chapters. Chapter one, focuses on the general introduction of the topic under view, stating the questions and hypothesis. Chapter two deals with the review of the related literature, philosophy and the history of VAT in Nigeria, along with some specific government responsibilities, and also general appraisal of …
Can the material for “Teacher Familiarity on high Order Thinking Skills in Science Classroom of Secondary School” be used as a guide for Science Education Project?
Yes it can be used — Higher Order Thinking Skills (HOTS) as the extended use of mind to face new challenges through critical thinking and creative thinking, both critical thinking and creative thinking are teachable and learnable components of HOTS. The aim of the study is to evaluate Teachers Familiarity on high Order Thinking Skills in Science Classroom of Secondary School. In achieving this aim, the following specific objectives were laid out to examine the performance of secondary school students that are familiar with the teachers, determine Teachers Familiarity on high Order Thinking Skills in Science Classroom of Secondary School, determine the relationship between Development of Higher Other Thinking Skills (HOTS) and their academic achievement scores, and investigate the effect of Teacher’s familiarity among Secondary Students …
Can this topic “Analysis of Stock Prices and Exchange Rate Interactions in Nigeria” be used for Economics Project?
Yes it can be utilized for research — The need to capture stock market and foreign exchange market nexus in Nigeria is underscored by the rapidly expanding financial markets integration due to trade and financial liberalization policies which seem to have enhanced the inflow of capital as well as accelerated investment/business interactions. Theoretically, the relationship between stock prices and exchange rate can be either positive or negative and can also run either way. This study therefore captures returns/mean and volatility spillovers between the stock and foreign exchange markets in Nigeria. The study empirically analyzes stock prices and exchange rate interactions with VAR and multivariate generalized autoregressive conditional heteroscedasticity (GARCH) models using monthly data from January 2000 to October 2014. The results of the E-G and Johansen cointegration test show …
Can this topic “The Effect of Single Parenthood on Learning Achievement Among Students in Junior Secondary Schools” be used for Education Project?
Yes it can be utilized for research — This study examined the effect of single parenthood on learning achievement among students in junior secondary schools. In carrying out the research, five research questions were asked to give directions. The participants for the study consisted of one hundred students randomly selected from two junior secondary schools in Odeda Local Government Area of Ogun State. The instrument used in data collection was questionnaire developed by the researcher. The data collected were statistically analysed using simple percentage. The result of the analysis revealed that parents’ socio-economic status, failure to provide learning materials and financial problems and economic hardship are factors that influences the learning achievement of student’s in school. Based on these findings, certain recommendations are made towards improving student’s learning …
Can the material for “The Application of Electronic Marketing in the Banking Service” be used as a guide for Banking and Finance (BF) Project?
Yes it can be used — The evolution of marketing, made us to understand it has been from the days of our ancestors and as such continue its growth. The reason that marketers are left working overtime daily created a belief that marketing activities may not grow beyond the orbit it is now. E- marketing is not different from marketing other than been operated in the Internet. The strategy rationale for the merge of fidelity bank PLC with the old FSB international Bank and Manny Bank PLC was to bring together banks of complementary competencies to create value in a vastly changing financial services market place. In this research work the hypothesis and the important of the study were stated, as the case study researcher, other …